digital tv tuner der virker under ubuntu

af mærket nova-t. Omkring 3-400 kr for den billigste i fona.
Jeg har een der fungerer ud af boxen med Upont0 8.10. Dvs mythtv og metv virker uden besvær.

jeg har god erfaring med tvtuner fra harald nyborg..

link: http://www.harald-nyborg.dk/merinfo.asp?varenr=3767&Grp=&n=10


install guide
http://groups.google.com/group/dk.edb.system.unix/browse_thread/thread/…

Tak det prøver jeg lige at se på ... tak for hjælpen !

Du skal være opmærksom på, at efter august(ca) lukkes det gamle digitale sendenet ned og det nye bliver officielt sat i værk. Det anbefales derfor, at du i stedet køber en digitaltuner med mpeg4 video modtagelses teknologi.

#4

Hmm er det ikke først i 2012 en mpg4 er påkrævet for at kunne modtage digitalt TV i Danmark, det har jeg da ihvertfald hørt. Det sendenet som lukkes ned i år er vist da nok det analoge.

i sidste del af den guide som du snubbi henviser til så der at man skal ligge firmwaren i en kerne. Hvordan er det lige jeg gør det ?

#1 + #2:
Må jeg spørge jer om i kan få DVB-subtitles (undertekster) på de digitale signaler med jeres kort. Hauppauge skulle angiveligt kunne klare det, hvad med Harald Nyborg?
(Jeg kører med en meget uelegant løsning med et HVR-1300 indstikskort, virker upåklageligt men uden tekstning (DVB-subtitles), selv om google siger at det kan lade sig gøre. Hvis jeg vil se noget ikke dansk/engelsk sproget må jeg fiske en "gammel" ekstern digital dekoder frem).

#0:
Hermed også været sagt at du skal være opmærksom på om kortet kan klare DVB-subtitles (og aktiveres i dit program), hvis du har brug for tekstning.

Hmm nu har jeg været i harald Nyborg og købe den. men altså måske kan jeg ikke følge den guide ordentligt eller noget. Men der sker ihvertfald ikke noget efter at ha fulgt den. Er der nogen der kan hjælpe lidt ?

her har jeg stillet det op som jeg installerer det.
husk at skrive korrekt sti til din kerne version...

boot linux med usb tuneren i .efter installation


1. sudo apt-get install mercurial linux-headers-$(uname -r) build-essential gcc make

2. wget http://www.telecable.es/personales/bbbaaa/dvb-usb-af9015.fw

3. sudo cp dvb-usb-af9015.fw /lib/firmware/2.6.27.9-generic
3. husk at skriv korrekt sti til din kerne.


4. hg clone http://linuxtv.org/hg/~anttip/af9015/archive/tip.tar.gz

5. cd tip.tar.gz

6. make && sudo make install

7. sudo gedit /etc/modules → include "dvb-usb-af9015"

8. og efterfølgende hentet en firmware-fil fra

http://www.otit.fi/~crope/v4l-dvb/af9015/af9015_firmware_cutter/firmwar…

og smidt den i /lib/firmware/2.6.24-16-generic/.
husk korrekt sti til din kerne version.

som afspiller bruger jeg me tv,

til #7 på tuneren fra harald nyborg virker underteksterne fint.

tak for det. Når jeg starter metv får jeg bare at vide "no tunerdevice"

mærkeligt ....


her er mit output i terminalen når jeg skriver dmesg

[ 0.565805] pci 0000:00:1f.0: quirk: region 0880-08bf claimed by ICH4 GPIO
[ 0.565825] PCI: 0000:00:1f.1 reg 10 io port: [1f0, 1f7]
[ 0.565833] PCI: 0000:00:1f.1 reg 14 io port: [3f4, 3f7]
[ 0.565840] PCI: 0000:00:1f.1 reg 18 io port: [170, 177]
[ 0.565847] PCI: 0000:00:1f.1 reg 1c io port: [374, 377]
[ 0.566008] PCI: 0000:00:1f.1 reg 20 io port: [ffa0, ffaf]
[ 0.566017] PCI: 0000:00:1f.1 reg 24 32bit mmio: [febffc00, febfffff]
[ 0.566046] PCI: 0000:00:1f.2 reg 10 io port: [fe00, fe07]
[ 0.566053] PCI: 0000:00:1f.2 reg 14 io port: [fe10, fe13]
[ 0.566060] PCI: 0000:00:1f.2 reg 18 io port: [fe20, fe27]
[ 0.566066] PCI: 0000:00:1f.2 reg 1c io port: [fe30, fe33]
[ 0.566073] PCI: 0000:00:1f.2 reg 20 io port: [fea0, feaf]
[ 0.566128] PCI: 0000:00:1f.3 reg 20 io port: [efe0, efff]
[ 0.566182] PCI: 0000:01:00.0 reg 10 32bit mmio: [e0000000, efffffff]
[ 0.566189] PCI: 0000:01:00.0 reg 14 io port: [de00, deff]
[ 0.566195] PCI: 0000:01:00.0 reg 18 32bit mmio: [fe9e0000, fe9effff]
[ 0.566213] PCI: 0000:01:00.0 reg 30 32bit mmio: [fea00000, fea1ffff]
[ 0.566229] pci 0000:01:00.0: supports D1
[ 0.566231] pci 0000:01:00.0: supports D2
[ 0.566254] PCI: 0000:01:00.1 reg 10 32bit mmio: [d0000000, dfffffff]
[ 0.566261] PCI: 0000:01:00.1 reg 14 32bit mmio: [fe9f0000, fe9fffff]
[ 0.566291] pci 0000:01:00.1: supports D1
[ 0.566293] pci 0000:01:00.1: supports D2
[ 0.566333] PCI: bridge 0000:00:01.0 io port: [d000, dfff]
[ 0.566337] PCI: bridge 0000:00:01.0 32bit mmio: [fe900000, feafffff]
[ 0.566342] PCI: bridge 0000:00:01.0 32bit mmio pref: [c8000000, efffffff]
[ 0.566379] PCI: 0000:02:01.0 reg 10 io port: [cd00, cdff]
[ 0.566386] PCI: 0000:02:01.0 reg 14 32bit mmio: [fe7fef00, fe7fefff]
[ 0.566412] PCI: 0000:02:01.0 reg 30 32bit mmio: [fe800000, fe80ffff]
[ 0.566427] pci 0000:02:01.0: supports D1
[ 0.566429] pci 0000:02:01.0: supports D2
[ 0.566431] pci 0000:02:01.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.566436] pci 0000:02:01.0: PME# disabled
[ 0.566465] PCI: 0000:02:02.0 reg 10 io port: [ce00, ceff]
[ 0.566507] pci 0000:02:02.0: supports D1
[ 0.566509] pci 0000:02:02.0: supports D2
[ 0.566541] PCI: 0000:02:08.0 reg 10 32bit mmio: [fe7ff000, fe7fffff]
[ 0.566548] PCI: 0000:02:08.0 reg 14 io port: [ccc0, ccff]
[ 0.566584] pci 0000:02:08.0: supports D1
[ 0.566585] pci 0000:02:08.0: supports D2
[ 0.566588] pci 0000:02:08.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.566592] pci 0000:02:08.0: PME# disabled
[ 0.566621] pci 0000:00:1e.0: transparent bridge
[ 0.566626] PCI: bridge 0000:00:1e.0 io port: [c000, cfff]
[ 0.566631] PCI: bridge 0000:00:1e.0 32bit mmio: [fe700000, fe8fffff]
[ 0.566646] bus 00 -> node 0
[ 0.566656] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[ 0.567221] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCI1._PRT]
[ 0.684917] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 9 10 *11 12 15)
[ 0.685267] ACPI: PCI Interrupt Link [LNKB] (IRQs *3 4 5 6 7 9 10 11 12 15)
[ 0.685614] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 *9 10 11 12 15)
[ 0.686117] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 9 *10 11 12 15)
[ 0.686466] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 *5 6 7 9 10 11 12 15)
[ 0.686809] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 9 10 11 12 15) *0, disabled.
[ 0.687158] ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 9 *10 11 12 15)
[ 0.687509] ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 *5 6 7 9 10 11 12 15)
[ 0.687780] Linux Plug and Play Support v0.97 (c) Adam Belay
[ 0.688059] pnp: PnP ACPI init
[ 0.688072] ACPI: bus type pnp registered
[ 0.712943] pnp 00:0a: io resource (0x800-0x85f) overlaps 0000:00:1f.0 BAR 7 (0x800-0x87f), disabling
[ 0.712948] pnp 00:0a: io resource (0x860-0x8ff) overlaps 0000:00:1f.0 BAR 7 (0x800-0x87f), disabling
[ 0.713803] pnp: PnP ACPI: found 11 devices
[ 0.713806] ACPI: ACPI bus type pnp unregistered
[ 0.713967] PnPBIOS: Disabled by ACPI PNP
[ 0.714464] PCI: Using ACPI for IRQ routing
[ 0.714615] NET: Registered protocol family 8
[ 0.714615] NET: Registered protocol family 20
[ 0.714615] NetLabel: Initializing
[ 0.714615] NetLabel: domain hash size = 128
[ 0.714615] NetLabel: protocols = UNLABELED CIPSOv4
[ 0.714615] NetLabel: unlabeled traffic allowed by default
[ 0.714615] hpet clockevent registered
[ 0.714615] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0
[ 0.714615] hpet0: 3 64-bit timers, 14318180 Hz
[ 0.717184] tracer: 772 pages allocated for 65536 entries of 48 bytes
[ 0.717188] actual entries 65620
[ 0.717406] AppArmor: AppArmor Filesystem Enabled
[ 0.717429] ACPI: RTC can wake from S4
[ 0.717506] system 00:00: iomem range 0x0-0x9ffff could not be reserved
[ 0.717511] system 00:00: iomem range 0x100000-0xffffff could not be reserved
[ 0.717514] system 00:00: iomem range 0x1000000-0x5ff73fff could not be reserved
[ 0.717517] system 00:00: iomem range 0xc0000-0xfffff could not be reserved
[ 0.717522] system 00:00: iomem range 0xfec00000-0xfec0ffff could not be reserved
[ 0.717525] system 00:00: iomem range 0xfee00000-0xfee0ffff could not be reserved
[ 0.717529] system 00:00: iomem range 0xfed20000-0xfed8ffff could not be reserved
[ 0.717533] system 00:00: iomem range 0xfecf0000-0xfecf0fff could not be reserved
[ 0.717537] system 00:00: iomem range 0xffb00000-0xffbfffff could not be reserved
[ 0.717540] system 00:00: iomem range 0xffc00000-0xffffffff could not be reserved
[ 0.717558] system 00:0a: ioport range 0xc00-0xc7f has been reserved
[ 0.753046] pci 0000:00:01.0: PCI bridge, secondary bus 0000:01
[ 0.753051] pci 0000:00:01.0: IO window: 0xd000-0xdfff
[ 0.753058] pci 0000:00:01.0: MEM window: 0xfe900000-0xfeafffff
[ 0.753063] pci 0000:00:01.0: PREFETCH window: 0x000000c8000000-0x000000efffffff
[ 0.753071] pci 0000:00:1e.0: PCI bridge, secondary bus 0000:02
[ 0.753075] pci 0000:00:1e.0: IO window: 0xc000-0xcfff
[ 0.753081] pci 0000:00:1e.0: MEM window: 0xfe700000-0xfe8fffff
[ 0.753086] pci 0000:00:1e.0: PREFETCH window: 0x00000070000000-0x000000700fffff
[ 0.753107] pci 0000:00:1e.0: setting latency timer to 64
[ 0.753112] bus: 00 index 0 io port: [0, ffff]
[ 0.753114] bus: 00 index 1 mmio: [0, ffffffff]
[ 0.753117] bus: 01 index 0 io port: [d000, dfff]
[ 0.753119] bus: 01 index 1 mmio: [fe900000, feafffff]
[ 0.753122] bus: 01 index 2 mmio: [c8000000, efffffff]
[ 0.753124] bus: 01 index 3 mmio: [0, 0]
[ 0.753126] bus: 02 index 0 io port: [c000, cfff]
[ 0.753129] bus: 02 index 1 mmio: [fe700000, fe8fffff]
[ 0.753131] bus: 02 index 2 mmio: [70000000, 700fffff]
[ 0.753134] bus: 02 index 3 io port: [0, ffff]
[ 0.753136] bus: 02 index 4 mmio: [0, ffffffff]
[ 0.753152] NET: Registered protocol family 2
[ 0.753348] IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.753769] TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
[ 0.755065] TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
[ 0.755784] TCP: Hash tables configured (established 131072 bind 65536)
[ 0.755790] TCP reno registered
[ 0.756215] NET: Registered protocol family 1
[ 0.756380] checking if image is initramfs... it is
[ 1.215953] Switched to high resolution mode on CPU 0
[ 1.593655] Freeing initrd memory: 8312k freed
[ 1.594038] Simple Boot Flag value 0x87 read from CMOS RAM was invalid
[ 1.594041] Simple Boot Flag at 0x7a set to 0x1
[ 1.594657] audit: initializing netlink socket (disabled)
[ 1.594680] type=2000 audit(1232228342.592:1): initialized
[ 1.600095] highmem bounce pool size: 64 pages
[ 1.600105] HugeTLB registered 4 MB page size, pre-allocated 0 pages
[ 1.603017] VFS: Disk quotas dquot_6.5.1
[ 1.603138] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 1.603277] msgmni has been set to 1752
[ 1.603456] io scheduler noop registered
[ 1.603460] io scheduler anticipatory registered
[ 1.603463] io scheduler deadline registered
[ 1.603482] io scheduler cfq registered (default)
[ 1.603581] pci 0000:01:00.0: Boot video device
[ 1.603597] pci 0000:02:08.0: Firmware left e100 interrupts enabled; disabling
[ 1.604068] isapnp: Scanning for PnP cards...
[ 1.957822] isapnp: No Plug & Play device found
[ 2.013263] Serial: 8250/16550 driver4 ports, IRQ sharing enabled
[ 2.013404] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 2.014497] 00:08: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 2.016871] brd: module loaded
[ 2.016962] input: Macintosh mouse button emulation as /devices/virtual/input/input0
[ 2.017128] PNP: PS/2 Controller [PNP0303:KBD] at 0x60,0x64 irq 1
[ 2.017132] PNP: PS/2 appears to have AUX port disabled, if this is incorrect please boot with i8042.nopnp
[ 2.017765] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 2.018517] mice: PS/2 mouse device common for all mice
[ 2.018734] rtc_cmos 00:05: rtc core: registered rtc_cmos as rtc0
[ 2.018760] rtc0: alarms up to one day, hpet irqs
[ 2.018923] EISA: Probing bus 0 at eisa.0
[ 2.018961] EISA: Detected 0 cards.
[ 2.018966] cpuidle: using governor ladder
[ 2.018969] cpuidle: using governor menu
[ 2.019586] TCP cubic registered
[ 2.019628] Using IPI No-Shortcut mode
[ 2.019969] registered taskstats version 1
[ 2.020167] Magic number: 9:606:702
[ 2.020320] rtc_cmos 00:05: setting system clock to 2009-01-17 21:39:04 UTC (1232228344)
[ 2.020324] BIOS EDD facility v0.16 2004-Jun-25, 0 devices found
[ 2.020326] EDD information not available.
[ 2.020851] Freeing unused kernel memory: 424k freed
[ 2.020911] Write protecting the kernel text: 2580k
[ 2.020946] Write protecting the kernel read-only data: 940k
[ 2.047452] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input1
[ 2.099744] compcache: Compressed swap size set to: 388152 KB
[ 2.100946] TLSF: pool: f8816000, init_size=16384, max_size=0, grow_size=16384
[ 2.320053] fuse init (API version 7.9)
[ 2.603862] processor ACPI0007:00: registered as cooling_device0
[ 3.336137] usbcore: registered new interface driver usbfs
[ 3.336171] usbcore: registered new interface driver hub
[ 3.336229] usbcore: registered new device driver usb
[ 3.345293] ehci_hcd 0000:00:1d.7: PCI INT D -> GSI 23 (level, low) -> IRQ 23
[ 3.345309] ehci_hcd 0000:00:1d.7: setting latency timer to 64
[ 3.345314] ehci_hcd 0000:00:1d.7: EHCI Host Controller
[ 3.345388] ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 1
[ 3.349303] ehci_hcd 0000:00:1d.7: debug port 1
[ 3.349311] ehci_hcd 0000:00:1d.7: cache line size of 128 is not supported
[ 3.349327] ehci_hcd 0000:00:1d.7: irq 23, io mem 0xffa80800
[ 3.360177] USB Universal Host Controller Interface driver v3.0
[ 3.384226] No dock devices found.
[ 3.404374] ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
[ 3.404631] usb usb1: configuration #1 chosen from 1 choice
[ 3.404677] hub 1-0:1.0: USB hub found
[ 3.404693] hub 1-0:1.0: 8 ports detected
[ 3.473773] SCSI subsystem initialized
[ 3.477403] via-rhine.c:v1.10-LK1.4.3 2007-03-06 Written by Donald Becker
[ 3.484021] e100: Intel(R) PRO/100 Network Driver, 3.5.23-k4-NAPI
[ 3.484026] e100: Copyright(c) 1999-2006 Intel Corporation
[ 3.576068] libata version 3.00 loaded.
[ 3.612382] uhci_hcd 0000:00:1d.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 3.612395] uhci_hcd 0000:00:1d.0: setting latency timer to 64
[ 3.612400] uhci_hcd 0000:00:1d.0: UHCI Host Controller
[ 3.612434] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 2
[ 3.612470] uhci_hcd 0000:00:1d.0: irq 16, io base 0x0000ff80
[ 3.612614] usb usb2: configuration #1 chosen from 1 choice
[ 3.612648] hub 2-0:1.0: USB hub found
[ 3.612660] hub 2-0:1.0: 2 ports detected
[ 3.732554] Adding 388148k swap on /dev/ramzswap0. Priority:100 extents:1 across:388148k
[ 3.820352] uhci_hcd 0000:00:1d.1: PCI INT B -> GSI 19 (level, low) -> IRQ 19
[ 3.820365] uhci_hcd 0000:00:1d.1: setting latency timer to 64
[ 3.820370] uhci_hcd 0000:00:1d.1: UHCI Host Controller
[ 3.820406] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 3
[ 3.820442] uhci_hcd 0000:00:1d.1: irq 19, io base 0x0000ff60
[ 3.820578] usb usb3: configuration #1 chosen from 1 choice
[ 3.820614] hub 3-0:1.0: USB hub found
[ 3.820626] hub 3-0:1.0: 2 ports detected
[ 3.836067] usb 1-4: new high speed USB device using ehci_hcd and address 3
[ 3.981459] usb 1-4: configuration #1 chosen from 1 choice
[ 4.028362] uhci_hcd 0000:00:1d.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18
[ 4.028375] uhci_hcd 0000:00:1d.2: setting latency timer to 64
[ 4.028379] uhci_hcd 0000:00:1d.2: UHCI Host Controller
[ 4.028415] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 4
[ 4.028452] uhci_hcd 0000:00:1d.2: irq 18, io base 0x0000ff40
[ 4.028590] usb usb4: configuration #1 chosen from 1 choice
[ 4.028633] hub 4-0:1.0: USB hub found
[ 4.028646] hub 4-0:1.0: 2 ports detected
[ 4.236809] uhci_hcd 0000:00:1d.3: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 4.236822] uhci_hcd 0000:00:1d.3: setting latency timer to 64
[ 4.236827] uhci_hcd 0000:00:1d.3: UHCI Host Controller
[ 4.236874] uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 5
[ 4.236902] uhci_hcd 0000:00:1d.3: irq 16, io base 0x0000ff20
[ 4.237099] usb usb5: configuration #1 chosen from 1 choice
[ 4.237135] hub 5-0:1.0: USB hub found
[ 4.237147] hub 5-0:1.0: 2 ports detected
[ 4.376051] usb 2-1: new full speed USB device using uhci_hcd and address 2
[ 4.444445] via-rhine 0000:02:01.0: PCI INT A -> GSI 22 (level, low) -> IRQ 22
[ 4.450047] eth0: VIA Rhine III at 0xfe7fef00, 00:05:5d:80:5f:e4, IRQ 22.
[ 4.450758] eth0: MII PHY found at address 1, status 0x786d advertising 01e1 Link 45e1.
[ 4.450805] e100 0000:02:08.0: PCI INT A -> GSI 20 (level, low) -> IRQ 20
[ 4.474117] e100 0000:02:08.0: PME# disabled
[ 4.479833] e100: eth1: e100_probe: addr 0xfe7ff000, irq 20, MAC addr 00:07:e9:67:68:c3
[ 4.486079] ata_piix 0000:00:1f.1: version 2.12
[ 4.486096] ata_piix 0000:00:1f.1: PCI INT A -> GSI 18 (level, low) -> IRQ 18
[ 4.486150] ata_piix 0000:00:1f.1: setting latency timer to 64
[ 4.486696] scsi0 : ata_piix
[ 4.486838] scsi1 : ata_piix
[ 4.486889] ata1: PATA max UDMA/100 cmd 0x1f0 ctl 0x3f6 bmdma 0xffa0 irq 14
[ 4.486892] ata2: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0xffa8 irq 15
[ 4.562715] usb 2-1: configuration #1 chosen from 1 choice
[ 4.676050] usb 4-1: new full speed USB device using uhci_hcd and address 2
[ 4.704528] ata1.00: ATA-6: ST380011A, 3.04, max UDMA/100
[ 4.704533] ata1.00: 156301488 sectors, multi 8: LBA48
[ 4.720444] ata1.00: configured for UDMA/100
[ 4.842697] usb 4-1: configuration #1 chosen from 1 choice
[ 4.848416] hub 4-1:1.0: USB hub found
[ 4.855181] hub 4-1:1.0: 7 ports detected
[ 4.900308] ata2.00: ATAPI: LITE-ON DVDRW SHW-16H5S, LS0H, max UDMA/66
[ 4.900328] ata2.00: limited to UDMA/33 due to 40-wire cable
[ 4.932260] ata2.00: configured for UDMA/33
[ 4.932407] scsi 0:0:0:0: Direct-Access ATA ST380011A 3.04 PQ: 0 ANSI: 5
[ 4.933365] scsi 1:0:0:0: CD-ROM LITE-ON DVDRW SHW-16H5S LS0H PQ: 0 ANSI: 5
[ 4.933485] ata_piix 0000:00:1f.2: PCI INT A -> GSI 18 (level, low) -> IRQ 18
[ 4.933492] ata_piix 0000:00:1f.2: MAP [ P0 -- P1 -- ]
[ 4.933545] ata_piix 0000:00:1f.2: setting latency timer to 64
[ 4.935432] scsi2 : ata_piix
[ 4.935874] scsi3 : ata_piix
[ 4.935938] ata3: SATA max UDMA/133 cmd 0xfe00 ctl 0xfe10 bmdma 0xfea0 irq 18
[ 4.935943] ata4: SATA max UDMA/133 cmd 0xfe20 ctl 0xfe30 bmdma 0xfea8 irq 18
[ 5.188020] usb 4-2: new low speed USB device using uhci_hcd and address 3
[ 5.366629] usb 4-2: configuration #1 chosen from 1 choice
[ 5.480025] usb 5-2: new full speed USB device using uhci_hcd and address 2
[ 5.600025] usb 5-2: device descriptor read/64, error -71
[ 5.824015] usb 5-2: device descriptor read/64, error -71
[ 6.040025] usb 5-2: new full speed USB device using uhci_hcd and address 3
[ 6.160021] usb 5-2: device descriptor read/64, error -71
[ 6.384018] usb 5-2: device descriptor read/64, error -71
[ 6.600047] usb 5-2: new full speed USB device using uhci_hcd and address 4
[ 7.008013] usb 5-2: device not accepting address 4, error -71
[ 7.120017] usb 5-2: new full speed USB device using uhci_hcd and address 5
[ 7.528014] usb 5-2: device not accepting address 5, error -71
[ 7.528036] hub 5-0:1.0: unable to enumerate USB device on port 2
[ 7.601908] usb 4-1.3: new full speed USB device using uhci_hcd and address 4
[ 7.949228] usb 4-1.3: configuration #1 chosen from 1 choice
[ 7.960109] usbcore: registered new interface driver libusual
[ 7.972845] usbcore: registered new interface driver hiddev
[ 7.975965] Initializing USB Mass Storage driver...
[ 7.979597] scsi4 : SCSI emulation for USB Mass Storage devices
[ 7.980078] usb-storage: device found at 3
[ 7.980082] usb-storage: waiting for device to settle before scanning
[ 7.987259] input: Logitech USB Receiver as /devices/pci0000:00/0000:00:1d.2/usb4/4-2/4-2:1.0/input/input2
[ 7.995825] scsi 0:0:0:0: Attached scsi generic sg0 type 0
[ 7.995877] scsi 1:0:0:0: Attached scsi generic sg1 type 5
[ 7.999454] input,hidraw0: USB HID v1.10 Keyboard [Logitech USB Receiver] on usb-0000:00:1d.2-2
[ 8.031508] input: Logitech USB Receiver as /devices/pci0000:00/0000:00:1d.2/usb4/4-2/4-2:1.1/input/input3
[ 8.032104] input,hidraw1: USB HID v1.10 Mouse [Logitech USB Receiver] on usb-0000:00:1d.2-2
[ 8.032163] usbcore: registered new interface driver usb-storage
[ 8.032168] USB Mass Storage support registered.
[ 8.032344] usbcore: registered new interface driver usbhid
[ 8.032349] usbhid: v2.6:USB HID core driver
[ 8.662115] Driver 'sd' needs updating - please use bus_type methods
[ 8.664822] sd 0:0:0:0: [sda] 156301488 512-byte hardware sectors (80026 MB)
[ 8.664847] sd 0:0:0:0: [sda] Write Protect is off
[ 8.664851] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 8.664890] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 8.664992] sd 0:0:0:0: [sda] 156301488 512-byte hardware sectors (80026 MB)
[ 8.665013] sd 0:0:0:0: [sda] Write Protect is off
[ 8.665016] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 8.665052] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 8.665058] sda:<4>Driver 'sr' needs updating - please use bus_type methods
[ 8.685671] sda1 sda2 < sda5 >
[ 8.704486] sd 0:0:0:0: [sda] Attached SCSI disk
[ 8.709938] sr0: scsi3-mmc drive: 48x/48x writer cd/rw xa/form2 cdda tray
[ 8.709945] Uniform CD-ROM driver Revision: 3.20
[ 8.710082] sr 1:0:0:0: Attached scsi CD-ROM sr0
[ 9.023625] PM: Starting manual resume from disk
[ 9.023630] PM: Resume from partition 8:5
[ 9.023632] PM: Checking hibernation image.
[ 9.023855] PM: Resume from disk failed.
[ 9.074526] kjournald starting. Commit interval 5 seconds
[ 9.074546] EXT3-fs: mounted filesystem with ordered data mode.
[ 12.980206] usb-storage: device scan complete
[ 12.980794] scsi 4:0:0:0: Direct-Access Generic USB SD Reader 1.00 PQ: 0 ANSI: 0
[ 12.981419] scsi 4:0:0:1: Direct-Access Generic USB CF Reader 1.01 PQ: 0 ANSI: 0
[ 12.982042] scsi 4:0:0:2: Direct-Access Generic USB SM Reader 1.02 PQ: 0 ANSI: 0
[ 12.982542] scsi 4:0:0:3: Direct-Access Generic USB MS Reader 1.03 PQ: 0 ANSI: 0
[ 12.983762] sd 4:0:0:0: [sdb] Attached SCSI removable disk
[ 12.983947] sd 4:0:0:0: Attached scsi generic sg2 type 0
[ 12.984867] sd 4:0:0:1: [sdc] Attached SCSI removable disk
[ 12.984960] sd 4:0:0:1: Attached scsi generic sg3 type 0
[ 12.985994] sd 4:0:0:2: [sdd] Attached SCSI removable disk
[ 12.986095] sd 4:0:0:2: Attached scsi generic sg4 type 0
[ 12.986986] sd 4:0:0:3: [sde] Attached SCSI removable disk
[ 12.987083] sd 4:0:0:3: Attached scsi generic sg5 type 0
[ 15.958682] udevd version 124 started
[ 16.784226] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[ 16.848834] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[ 16.924210] Linux agpgart interface v0.103
[ 17.004344] agpgart-intel 0000:00:00.0: Intel 865 Chipset
[ 17.011351] agpgart-intel 0000:00:00.0: AGP aperture is 128M @ 0xc0000000
[ 17.088213] iTCO_vendor_support: vendor-support=0
[ 17.160202] iTCO_wdt: Intel TCO WatchDog Timer Driver v1.03 (30-Apr-2008)
[ 17.168196] iTCO_wdt: Found a ICH5 or ICH5R TCO device (Version=1, TCOBASE=0x0860)
[ 17.168370] iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0)
[ 17.294198] input: Power Button (FF) as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input4
[ 17.304038] ACPI: Power Button (FF) [PWRF]
[ 17.304196] input: Power Button (CM) as /devices/LNXSYSTM:00/device:00/PNP0C0C:00/input/input5
[ 17.316054] ACPI: Power Button (CM) [VBTN]
[ 17.348203] intel_rng: Firmware space is locked read-only. If you can't or
[ 17.348206] intel_rng: don't want to disable this in firmware setup, and if
[ 17.348208] intel_rng: you are certain that your system has a functional
[ 17.348209] intel_rng: RNG, try using the 'no_fwh_detect' option.
[ 18.002079] parport_pc 00:09: reported by Plug and Play ACPI
[ 18.002130] parport0: PC-style at 0x378 (0x778), irq 7, using FIFO [PCSPP,TRISTATE,COMPAT,ECP]
[ 18.107085] fglrx: module license 'Proprietary. (C) 2002 - ATI Technologies, Starnberg, GERMANY' taints kernel.
[ 18.345652] [fglrx] Maximum main memory to use for locked dma buffers: 1411 MBytes.
[ 18.345789] [fglrx] vendor: 1002 device: 4150 count: 1
[ 18.346192] [fglrx] ioport: bar 1, base 0xde00, size: 0x100
[ 18.346211] pci 0000:01:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 18.346670] [fglrx] PAT is enabled successfully!
[ 18.346711] [fglrx] module loaded - fglrx 8.55.2 [Oct 28 2008] with 1 minors
[ 18.932512] Linux video capture interface: v2.00
[ 19.048212] gspca: main v2.4.0 registered
[ 19.213720] gspca: probing 041e:4052
[ 19.420937] ov519: I2C synced in 0 attempt(s)
[ 19.420941] ov519: starting OV7xx0 configuration
[ 19.432889] ov519: Sensor is an OV7670
[ 20.222575] end_request: I/O error, dev sr0, sector 0
[ 20.222585] Buffer I/O error on device sr0, logical block 0
[ 20.222591] Buffer I/O error on device sr0, logical block 1
[ 20.222598] Buffer I/O error on device sr0, logical block 2
[ 20.222602] Buffer I/O error on device sr0, logical block 3
[ 20.222607] Buffer I/O error on device sr0, logical block 4
[ 20.222612] Buffer I/O error on device sr0, logical block 5
[ 20.222617] Buffer I/O error on device sr0, logical block 6
[ 20.222621] Buffer I/O error on device sr0, logical block 7
[ 20.224283] end_request: I/O error, dev sr0, sector 0
[ 20.224291] Buffer I/O error on device sr0, logical block 0
[ 20.225870] end_request: I/O error, dev sr0, sector 4
[ 20.225876] Buffer I/O error on device sr0, logical block 1
[ 20.391283] input: PC Speaker as /devices/platform/pcspkr/input/input6
[ 20.581068] C-Media PCI 0000:02:02.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17
[ 20.777922] gspca: probe ok
[ 20.777994] usbcore: registered new interface driver ov519
[ 20.778021] ov519: registered
[ 20.800054] usblp0: USB Bidirectional printer dev 4 if 0 alt 0 proto 2 vid 0x04F9 pid 0x000D
[ 20.800086] usbcore: registered new interface driver usblp
[ 20.809073] dcdbas dcdbas: Dell Systems Management Base Driver (version 5.6.0-3.2)
[ 23.891002] lp0: using parport0 (interrupt-driven).
[ 24.017184] usbcore: registered new interface driver dvb_usb_af9015
[ 24.231794] Adding 3229024k swap on /dev/sda5. Priority:-1 extents:1 across:3229024k
[ 24.820862] EXT3 FS on sda1, internal journal
[ 26.069117] type=1505 audit(1232228368.352:2): operation="profile_load" name="/usr/share/gdm/guest-session/Xsession" name2="default" pid=4113
[ 26.283345] type=1505 audit(1232228368.564:3): operation="profile_load" name="/usr/lib/cups/backend/cups-pdf" name2="default" pid=4118
[ 26.283691] type=1505 audit(1232228368.564:4): operation="profile_load" name="/usr/sbin/cupsd" name2="default" pid=4118
[ 26.354751] type=1505 audit(1232228368.636:5): operation="profile_load" name="/usr/sbin/mysqld" name2="default" pid=4122
[ 26.542587] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 27.398101] ACPI: WMI: Mapper loaded
[ 28.623158] warning: `avahi-daemon' uses 32-bit capabilities (legacy support in use)
[ 28.892146] NET: Registered protocol family 10
[ 28.894691] lo: Disabled Privacy Extensions
[ 31.371791] apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16ac)
[ 31.371798] apm: overridden by ACPI.
[ 31.780360] ppdev: user-space parallel port driver
[ 33.714948] vboxdrv: Trying to deactivate the NMI watchdog permanently...
[ 33.714956] vboxdrv: Successfully done.
[ 33.714959] vboxdrv: Found 1 processor cores.
[ 33.717296] vboxdrv: TSC mode is 'synchronous', kernel timer mode is 'normal'.
[ 33.717307] vboxdrv: Successfully loaded version 2.0.4_OSE (interface 0x00090000).
[ 39.452030] usb 5-2: new full speed USB device using uhci_hcd and address 6
[ 39.572543] usb 5-2: device descriptor read/64, error -71
[ 39.685237] Bluetooth: Core ver 2.13
[ 39.688234] NET: Registered protocol family 31
[ 39.688240] Bluetooth: HCI device and connection manager initialized
[ 39.688247] Bluetooth: HCI socket layer initialized
[ 39.758908] Bluetooth: L2CAP ver 2.11
[ 39.758915] Bluetooth: L2CAP socket layer initialized
[ 39.775627] Bluetooth: SCO (Voice Link) ver 0.6
[ 39.775637] Bluetooth: SCO socket layer initialized
[ 39.808031] usb 5-2: device descriptor read/64, error -71
[ 39.937262] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[ 39.937269] Bluetooth: BNEP filters: protocol multicast
[ 39.999296] Bridge firewalling registered
[ 40.024032] usb 5-2: new full speed USB device using uhci_hcd and address 7
[ 40.204022] usb 5-2: device descriptor read/64, error -71
[ 40.432016] usb 5-2: device descriptor read/64, error -71
[ 40.648016] usb 5-2: new full speed USB device using uhci_hcd and address 8
[ 41.056014] usb 5-2: device not accepting address 8, error -71
[ 41.168016] usb 5-2: new full speed USB device using uhci_hcd and address 9
[ 41.576011] usb 5-2: device not accepting address 9, error -71
[ 41.576235] hub 5-0:1.0: unable to enumerate USB device on port 2
[ 41.607444] Bluetooth: RFCOMM socket layer initialized
[ 41.607805] Bluetooth: RFCOMM TTY layer initialized
[ 41.607812] Bluetooth: RFCOMM ver 1.10
[ 44.233606] [fglrx] AGP detected, AgpState = 0x1f004a1b (hardware caps of chipset)
[ 44.233616] [fglrx] [agp] enabling AGP with mode=0x1f004b1a
[ 44.233621] agpgart-intel 0000:00:00.0: AGP 3.0 bridge
[ 44.233643] agpgart-intel 0000:00:00.0: putting AGP V3 device into 8x mode
[ 44.233677] fglrx_pci 0000:01:00.0: putting AGP V3 device into 8x mode
[ 44.233707] [fglrx] AGP enabled, AgpCommand = 0x1f004312 (selected caps)
[ 45.770084] ADDRCONF(NETDEV_UP): eth1: link is not ready
[ 45.787676] eth0: link up, 100Mbps, full-duplex, lpa 0x45E1
[ 45.976174] NET: Registered protocol family 17
[ 48.302523] [fglrx] Setup AGP aperture
[ 48.303321] [fglrx] GART Table is not in FRAME_BUFFER range
[ 48.349581] [fglrx] Reserved FB block: Shared offset:0, size:40000
[ 55.976011] eth0: no IPv6 routers present
[ 99.588725] process `skype' is using obsolete setsockopt SO_BSDCOMPAT
[ 152.836030] usb 5-2: new full speed USB device using uhci_hcd and address 10
[ 152.960031] usb 5-2: device descriptor read/64, error -71
[ 153.188034] usb 5-2: device descriptor read/64, error -71
[ 153.404029] usb 5-2: new full speed USB device using uhci_hcd and address 11
[ 153.524027] usb 5-2: device descriptor read/64, error -71
[ 153.748093] usb 5-2: device descriptor read/64, error -71
[ 153.964026] usb 5-2: new full speed USB device using uhci_hcd and address 12
[ 154.372026] usb 5-2: device not accepting address 12, error -71
[ 154.484025] usb 5-2: new full speed USB device using uhci_hcd and address 13
[ 154.892078] usb 5-2: device not accepting address 13, error -71
[ 154.892535] hub 5-0:1.0: unable to enumerate USB device on port 2
[ 154.932571] ppdev0: registered pardevice
[ 154.980268] ppdev0: unregistered pardevice
[ 155.136142] ppdev0: registered pardevice
[ 155.184101] ppdev0: unregistered pardevice
[ 156.270974] ppdev0: registered pardevice
[ 156.320395] ppdev0: unregistered pardevice

hvis du følger vejledningen skulle det gerne virke, har lige selv installeret det efter guiden på min pc nr 2. har du smidt firmwaren i /lib/firmware/sti til kerne...

ja det skulle den være .... måske downloader jeg firmwaren forkert...... man højreklikker bare og vælger gem som og så ligger man den ind i lib/firmware/2.6.27-11-generic ikke ?

jeg bruger
wget http://www.otit.fi/~crope/v4l-dvb/af9015/af9015_firmware_cutter/firmwar…

og flytter dvb-usb-af9015.fw over i /lib/firmware/min kerne version

har du skrevet dvb-usb-af9015 ind i /etc/modules/



# /etc/modules: kernel modules to load at boot time.
#
# This file contains the names of kernel modules that should be loaded
# at boot time, one per line. Lines beginning with "#" are ignored.
dvb-usb-af9015
fuse
lp

...

prøv evt at slette mappen tip.tar.gz og starte helt forfra igen.

nu virker det mærkeligvis hehe

dog med en hel del striber men det har vel noget med modtageforholdene at gøre... dog får jeg en besked i metv der står

"failed to create node: node was NULL"

Hvad kan det betyde ?'

husk hvergang du opdaterer til ny kerne version skal du installere det til ny kerne brug trin 3 til 6.
hvad "failed to create node: node was NULL" måske indstillings problem med me tv prøv at google.

hej igen ... ja det forsvant da jeg genstartede... så det er godt .... har du din infra røde fjernbetjening til at virke ? det gør den nemlig ikke her..... skal lirc installeres for at det virker eller hvordan har du det sat op ?

nej har ikke rodet med fjernbetjening. så ved ikke om den kan komme til at virke. prøver nok en dag hvor jeg får god tid...